PV Measuring

Elma 2200X is a re-invention of the voltage tester- again. Elma 2200X offers all the same and clever functions as the well-known Elma 2100X, but the test leads and instrument are en even more rugged quality. Furthermore the instrument can load the point of measurement, to discharge induced voltages, and for simple RCD test, providing a load of 30mA at 230V.

We've never seen so many clever functions in a simple voltage tester, making the instrument suitable for about every task an electrician meet, also when legislation demands to use a tester in compliance with the voltage tester directive.

• Perfect for measuring on charging sockets and charging stands EVSE for electric cars
• Voltagetest, 2 pole with LED 12…1.000V AC/DC
• Voltage measurement with digital display 6…1.000V/1.500V AC/DC
• Continuity
• Resistance 0-1999Ω
• Single pole phase test
• Phase rotation test
• Large and bright display and bright LED's
• Selftest and auto on/off function
• LED warning when dangerous voltage
• Fulfills voltage tester directive
• Very rugged test leads
• Changeable test tips 2/4mm
• Bright torch light

Elma 2200X fulfills IEC 61010-1 KAT IV 600V / IEC 61243-3:2014 and is provided ready to use with batteries and manual.

Z200 PV Analyzer - Solar PV testing and fast troubleshooting

Standard Photovoltaic Measurements
- PV string voltage Voc
- PV string current Isc
- PV system isolation resistance Riso
- PV string series resistance Rs
- PV string impedance curves (overall degradation check)

Fault Position measurements
- Position of ground (Riso) faults in PV strings
- Position of disconnect in PV strings
- Tone generator and acoustic pickup for cable tracing (Accessory)

Single Module Measurements
- Module bypass diode check (open or short diode)
- Module shunting resistance (PID and degradation check)
- Module voltage check

Special Software Features
- State machine algorithm to help the user analyse fault scenarios
- Integrated timer function for periodic ground faults
- Build in PDF report generator

Test lead for the most demanding measurement tasks.

With a cross-section of 2.5 mm² and an outer jacket made of silicone, this test lead is both flexible and robust, while the length of 200 cm is sufficient for most measurement tasks.

Safety category CAT IV 1000 V.

Test lead for the most demanding measurement tasks.

With a cross-section of 2.5 mm² and an outer jacket made of silicone, this test lead is both flexible and robust, while the length of 200 cm is sufficient for most measurement tasks.

Safety category CAT IV 1000 V.

Test lead for the most demanding measurement tasks.

With a cross-section of 2.5 mm² and an outer jacket made of silicone, this test lead is both flexible and robust, while the length of 200 cm is sufficient for most measurement tasks.

Safety category CAT IV 1000 V.

Test lead for the most demanding measurement tasks.

With a cross-section of 2.5 mm² and an outer jacket made of silicone, this test lead is both flexible and robust, while the length of 200 cm is sufficient for most measurement tasks.

Safety category CAT IV 1000 V.

PVF2317 is a test lead specifically designed for measurements on solar circuits and can be used to measure open-circuit voltage, short-circuit current, and insulation resistance.

To facilitate connection and disconnection, the MC4 connector is without a locking mechanism.

PVF2317 is robustly constructed with a 2.5 mm² cross-section and categorized as CAT III 1500 V/CAT IV 1000 V.

PVM2317 is a test lead specifically designed for measurements on solar circuits and can be used to measure open-circuit voltage, short-circuit current, and insulation resistance.

PVM2317 is robustly constructed with a 2.5 mm² cross-section and categorized as CAT III 1500 V/CAT IV 1000 V.

PVFM2317 is a test lead specially designed for performance measurements on the DC side of solar power systems.

The MC4 connectors allow the cable to be inserted into the DC circuit, e.g., between the panel and the inverter, enabling measurement of operating current with a clampmeter, while the banana plug provides access to voltage measurement.

PVFM2317 is robustly constructed with a 2.5 mm² cross-section and categorized as CAT III 1500 V/CAT IV 1000 V.

PVMF2317 is a test lead specially designed for performance measurements on the DC side of solar power systems.

The MC4 connectors allow the cable to be inserted into the DC circuit, e.g., between the panel and the inverter, enabling measurement of operating current with a clampmeter, while the banana plug provides access to voltage measurement.

PVMF2317 is robustly constructed with a 2.5 mm² cross-section and categorized as CAT III 1500 V/CAT IV 1000 V.